Browse documentation
← EditorFind another guide
Editor

Trim, split, move, and remove timeline items

Timeline editing controls when content appears and how long it lasts. Work on one short section at a time: select the target, place the playhead, make the change, and play through the result. Check nearby text and audio as well as the picture.

On this page
What this guide helps you do

Adjust a sequence while keeping the intended timing, selection, and relationship between visual and audio items.

Before you begin

  • Open an editable project with content on the timeline and pause playback.
  • Save the project using your normal project save controls.
  • Check that the selected items and their layers are unlocked.

Understand what an edge changes

Dragging the body of a block moves it in time. Pulling an available edge changes its timing or duration. Changing Timeline zoom, Fit, or Zoom to selection only changes how much of the timeline you see.

The same timeline gesture has a different purpose for different content.
ItemTrimming meansCheck afterward
VideoChanging the source range played by the clip, within the available media.The first and last frames, and any sound in the clip.
ImageChanging how long the still image remains on screen.Its start, duration, and relationship to titles or narration.
Text, graphic, or subtitle itemChanging the item's visible time span where trimming is offered.Readability and timing against the spoken words or picture.
Voice or music itemChanging the sound segment used and its time on the timeline.The start and end of the sound, plus synchronization with other layers.

Trim a beginning or ending

  1. Select and inspect

    Select the block and play around its boundary. Decide where the content should begin or end before moving an edge.

  2. Zoom in if needed

    Use Timeline zoom or Zoom to selection so the edges are easy to distinguish. Short blocks are harder to adjust when the whole project is visible.

  3. Pull the appropriate edge

    Drag the start or end handle. For a still image, the ending handle sets its screen duration. For source media, stay within the available content; trimming cannot reveal footage that is not in the source.

  4. Review the boundary

    Play from just before the change to just after it. Check for a cut-off word, an image that ends too soon, a gap, or an overlap with the next item.

Split a section, then position it

To move one item, use Clear clip selection and select it again. Ungroup first if you need to separate it from a group. If the item or destination is locked, follow the displayed message.

In Settings, open Editor view and use Snapping to align moved items with nearby edges, the playhead, and markers. Turn it off for free placement. Timeline snapping applies to moving items, not to trimming their edges.

  1. Choose the split point

    Select the item and move the playhead inside it, leaving content on both sides. A playhead at the beginning, at the end, or in empty space cannot make an interior split.

  2. Open the item's actions

    Right-click the timeline block and choose Split at playhead when available. Confirm that the action is enabled for this item.

  3. Review both parts

    Check the two resulting items. For text or subtitles, splitting divides timing; review the wording as well. For audio, listen across the boundary before moving either part.

  4. Move the intended selection

    Drag the body of the block to a new time. A multiple selection or group can move together. Watch the highlighted items and destination layer, then release only when the placement matches your intention.

Remove only the intended content

Check the highlighted blocks and selected count, then use Delete selected clips in the timeline toolbar. A clip's Remove action is also available. Group membership can broaden a delete, so ungroup first when separating items.

With ripple mode off, deletion leaves the time range open. Check whether the gap is intentional. Removing a timeline item is separate from deleting its library file. Use Undo promptly if the selection was wrong.

Choose how to handle empty time

These additional operations appear in Pro editing mode. Ripple operations leave markers fixed. A gap with nothing after it has nothing to pull backward. Ripple delete can be refused if the selected range has gaps, other items cross it, or affected items are locked. Preserve intentional pauses and synchronization.

Gap closing and ripple editing are not interchangeable.
ActionWhat changesWhat to prepare
Close gap at playheadMoves later items on that layer backward by the gap length. Other layers stay in place.Put the playhead in a real gap and open that layer's menu.
Ripple delete selected clipsRemoves a clear, continuous selected time range and shifts later timeline items across layers.Check crossing items and downstream locks before deleting.
Toggle ripple deleteEnables ripple mode for toolbar deletion and for placing clips. Placement makes room by moving later clips on the destination layer.Check whether the mode is active before dragging or deleting.

Use Undo and confirm the new sequence

Undo and Redo are in the timeline toolbar and operate on the available edit history. Use one step at a time, checking the timeline after each step. They are not a substitute for a saved project version.

Review the changed section, including captions, narration, and the ending. Save when correct. If an operation repeatedly fails, contact support with the item type, intended edit, playhead time, selection or group details, and exact message.

Check your result

  • Only the intended items or group were affected.
  • Trimmed edges and split points play cleanly.
  • Images and text remain visible for the intended duration.
  • Gaps, overlaps, and audio synchronization have been reviewed.
  • Ripple mode is set deliberately and the edited project is saved.
Still have a question?

Tell us what you were trying to do and the message you saw.

Contact support
Trim, Split and Move Timeline Clips | ZOVOZ