Browse documentation
← Creator StudioFind another guide
Creator Studio

Attach narration and review section timing

Attach an existing voice-over to the section it belongs to, listen to the proposed take, and confirm it before replacement. Creator shows the audio's measured source duration separately from the script's planning times. Review the words, pictures, and captions together before continuing to Editor.

On this page
What this guide helps you do

Associate the correct narration with each section and understand which timing information is estimated, measured, or still awaiting review.

Before you begin

  • Save the current Creator project and select the intended episode and script section.
  • Prepare a WAV, MP3, M4A, or WebM voice-over of up to 10 MB, or use eligible audio already in this project.
  • Check the section's wording and keep the original recording available before replacing an existing take.

Distinguish planning time from measured audio

Attaching a voice-over does not automatically replace your section's planning times with the audio duration. The current voice-over area explicitly identifies script/audio and caption alignment as unverified.

The different timing values answer different questions.
Timing valueWhat it describesWhat it does not establish
Reading estimateA duration estimated from the current script text.The actual length of a spoken recording.
Custom section timingThe Start time and End time you choose for the section.That the narration or captions align with those times.
Measured source durationThe inspected length of the selected audio file.That its spoken words match the script or that captions are synchronized.
Target durationThe planned length for the episode.The verified duration of a finished export.

Choose a voice-over for the selected section

  1. Open the section's narration controls

    Select the script card, open Voice, and choose Narration. Confirm the section and speaker before selecting audio. In a section settings view, the same narration controls appear with the section's voice settings.

  2. Upload or reuse a source

    Choose Upload voice-over for a file on your device. Alternatively, use Existing project audio and choose an eligible item from Choose owned audio. This list belongs to the current project; a file from another project is not automatically an available section recording.

  3. Wait for inspection

    Creator checks the file and prepares a proposed voice-over player. Inspect the displayed duration and any error before continuing. A file without a readable playable duration cannot be attached through this review.

  4. Listen against the script

    Play the proposed take from beginning to end. Check the speaker, wording, pronunciation, leading silence, and ending. If silence information is unavailable, listen for it yourself.

Confirm the take before replacing narration

Discard selection removes the proposed choice before acceptance and leaves the current take in place. Remove voice-over detaches the current narration from the section. Use it deliberately rather than removing the working take just to test another file.

  1. Use or replace the selected section's voice-over

    Choose Use this voice-over when the section has no current take, or Replace section voice-over when replacing one. The acceptance applies to the selected section, so check its name and wording again before confirming.

  2. Check the attached result

    Look for the file name and Current section voice-over player. Read the duration label, such as Browser-measured source duration. A measurement describes the audio file; it is not a transcript or a word-by-word alignment.

  3. Save the association

    Use Save project after the accepted take is attached. An upload or preview alone is not confirmation that the section's new association has been saved.

Review and adjust the section's planning times

Planning times do not stretch a voice-over to fit. If a take is too long for the intended section, decide whether to revise the text, prepare another take, or adjust the plan and visuals.

  1. Open Timing

    For the selected script card, open Settings and Details to find Timing. Check Start time, End time, and the displayed duration.

  2. Choose estimated or custom timing

    Auto adjust to match script length uses the script's reading estimate. To set your own times, edit Start time or End time; this changes the section to custom timing.

  3. Use valid times

    Enter MM:SS, with the end after the start. A section duration cannot exceed 60 minutes. Compare the chosen range with the measured recording and leave appropriate room for pauses or visual transitions.

  4. Review neighboring sections

    Check the next section and the overall episode after a timing change. A change in reading estimates or a custom start can affect the planned sequence. Listen and review the intended order instead of relying on the total alone.

Recheck after changing text or audio

  • After editing the script, inspect the narration area. Script changed means the retained recording needs another review against the current wording.
  • Some accepted wording suggestions clear the section's audio association. If no voice-over is attached, choose and review the appropriate take again.
  • After replacing narration, compare its measured length with custom section times and the episode target. A new take can be longer or shorter even when the words are similar.
  • Review connected storyboard shots and captions. Measured source duration does not prove that either follows the spoken words.
  • Save the reviewed Creator changes before the handoff. Existing Editor work needs its own reviewed update; attaching narration does not silently rebuild that timeline.

Recover from a blocked attachment or playback problem

If the script or project changes during inspection, review the take again against the current section. Do not assume that a preview opened for one section was accepted for another.

If attachment is blocked, check that the project is saved, the section is editable, and the source type, size, and duration are supported. Review script protection before changing a protected section.

If the saved take will not play, use Retry saved narration. The playback error does not itself remove the association. Keep the original file and choose an approved replacement only after checking the problem.

If a long file cannot be inspected, prepare shorter section takes from your original recording. Check the new file's words and duration before attaching it; repeated upload attempts do not resolve an unreadable source.

Check your result

  • Each accepted take belongs to the intended episode, section, and speaker.
  • The file plays correctly and its measured duration is visible.
  • Reading estimates and custom timing have been distinguished from audio measurement.
  • Changed wording, visuals, captions, and any Editor handoff have been reviewed.
  • The section associations and other Creator edits are saved.
Still have a question?

Tell us what you were trying to do and the message you saw.

Contact support
Narration and Script Section Timing | ZOVOZ